XCBSQ, LTM-3A, LVDT Stroke Displacement Transmitter

XCBSQ, LTM-3A, LVDT stroke displacement transmitter technical parameters:

â—† External power supply: 220V AC or 24V DC
â—† Input
Signal: Receive a signal from a VS Series Vibration Speed ​​Sensor
Sensitivity: 20mV/mm/s±5%
Frequency response: 5 ~ 300Hz
◆ Range: 0 ~ 500μm (peak - peak) or 0 ~ 50.0mm / s (true RMS)
â—† LED indication: OK green, Alert, Danger red.
◆ Measurement error: ±1% of full scale
◆ Current output: 4~20mA active, output load ≤500Ω
◆ Alarm point setting: 0~100% full scale, accuracy ±1%
â—† Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal)
â—† Relay seal: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
â—† Power-on delay: about 10 seconds
◆ Temperature range: -25°C~+65°C during operation, -40°C~+85°C during storage
â—† Relative humidity: up to 95%, no condensation







Installation position: Install it vertically or horizontally on the vibration point to be tested. Fix the M10×1.5×10 screw on the bottom of the sensor to the tested housing, and then screw the sensor on it.

3.2 Installation Dimensions and Specifications: Refer to Figure 1. If the installation position of the transmitter is washed by high temperature steam, etc., in order to reduce the ambient temperature of the transmitter and provide protective measures, under normal circumstances, no protection is required.


The VB-Z210 integrated axial displacement signal transmitter is used with eddy current sensors and is widely used in large rotating machinery (such as steam turbines and compressors) in the power, metallurgy, petrochemical and paper industries.
Measurement and protection control of axial displacement of motors, fans, pumps, etc.
Fault monitoring monitors the axial displacement of the rotating machine rotor.
The position (displacement) of the parametric rotor relative to the bearing pad is measured.
Unit type

XCBSQ, LTM-3A, LVDT Stroke Displacement Transmitter

External power supply: 220V AC or 24V DC

Technical indicators:
Signal: Receive signal sensitivity of a ST series vibration speed sensor: 20mV/mm/s ± 5%
Frequency response: 5 ~ 300Hz
Range: 500μm (peak-to-peak) or 0-50.0mm/s (true RMS)
LED indication: OK green, Alert, Danger red
Measurement error: ±1% of full scale
Current output: 4-20mA active, output load ≤500Ω
Alarm point setting: 0-100% full scale, accuracy ± 1%
Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal),
Following electrical sealing: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
Power-on delay: about 10 seconds
Temperature range: -25°C to +65°C during operation
-40°C to +85°C during storage
Relative humidity: up to 95%, no condensation
Dimensions: 90W × 120L × 75Hmm
Installation size: 80×90mm
Weight: about 660g



JM-B-6Z monitoring and protection device, JM-B-6000 steam turbine monitoring and protection device, JM-B-3E dual-channel vibration monitoring and protection device,


SZC-04 series intelligent tachometer, SZC-04F series intelligent speed anti-rotometer, DZC-02A tachometer

Servo feeder machine is one type smart and easy to operate feeder machine in the market. It can feed metal strips thickness up to 6.0mm and Max. Feeding speed reaches 30m/min.

Operating with Computerize Numerical Control by PLC program from MITSUBISHI made in Japan, it can ensure +/-0.01mm high feeding precision.It is very important to precisely measure the feeding length of the sheet during sheet metal processing and length cutting, and when dealing with press.
This precision can only be achieved with a motor with a precise turning interval, such as a servo motor. We manufacture high-precision drivers by utilizing the capabilities of high-resolution servo motors. We design our machines according to the quality, width, and thickness of the materials you will be processing.

Directly input the 20 difference feeding length on the control display screen and then it can reach needed feeding length, the Max. Feeding length is 9999.99mm.

Usually Nc Servo Feeder matches with adjustment signal from the cutting machine or Power Press Machine.With two different release type, pneumatic release and mechanical release.


Servo Roll Feeder

NC Servo Roll Feeder,Nc Servo Roll Sheet Feeder,Servo Roller Feeder,Nc Servo Feeder,NC Servo,Coil Feeders

Mayflay Machinery(huizhou) Co.,LTD , https://www.pressfeeders.com